Description
Low-profile tilted through-hull single-band 1kW CHIRP fishfinder transducer
The SS175 is available in the Low, Medium or High bands, or in a Highband version with widebeam. All versions are available with zero, 12 deg or 20 deg tilt. This transducer is a stainless steel version of the B175C.
Specifications:
| Type | CHIRP single-band fishfinder transducer |
| Low Band | Frequency range 40-60 kHz / Beam width 32-21 degrees |
| Medium Band | Frequency range 85-135 kHz / Beam width 16-11 degrees |
| High Band | Frequency range 130-210 kHz / Beam width 10-6 degrees |
| High Wide Band | Frequency range 150-250 kHz / Beam width 25 degrees |
| Power Rating | 1000 watts |
| Mounting | Low-profile through-hull |
| Housing | Stainless Steel |
| Cable Length | 10 meters |
| Mix and Match | Yes |
| Temperature Sensor | Yes |
| Speed Sensor | ? |
| Retractable Insert | ? |
| Tilted | Yes |
| Status | In production |
| Reference Page |
Product Data Sheet
Base Models
These Mix and Match base models must be combined with a Mix and Match cable for installation. The suffix ‘-MM’ in the Gemeco part number designates a Mix and Match base model.
| Transducer | Code | Airmar Part # | Tilt | Description |
|---|---|---|---|---|
| SS175C-0-H-MM | 41-842-1-01 | 0 degrees | High Band, Zero deg tilt | |
| SS175C-0-HW-MM | 41-821-2-01 | 0 degrees | High Band, Widebeam, Zero deg tilt | |
| SS175C-0-L-MM | 41-832-2-01 | 0 degrees | Low Band, Zero deg tilt | |
| SS175C-0-M-MM | 41-830-2-01 | 0 degrees | Medium Band, Zero deg tilt | |
| SS175C-12-H-MM | 41-843-1-01 | 12 degrees | High Band, 12 deg tilt | |
| SS175C-12-HW-MM | 41-822-2-01 | 12 degrees | High Band, Widebeam, 12 deg tilt | |
| SS175C-12-L-MM | 41-833-2-01 | 12 degrees | Low Band, 12 deg tilt | |
| SS175C-12-M-MM | 41-831-2-01 | 12 degrees | Medium Band, 12 deg tilt | |
| SS175C-20-H-MM | 41-844-1-01 | 20 degrees | High Band, 20 deg tilt | |
| SS175C-20-HW-MM | 41-823-3-01 | 20 degrees | High Band, Widebeam, 20 deg tilt | |
| SS175C-20-L-MM | 41-820-3-01 | 20 degrees | Low Band, 20 deg tilt | |
| SS175C-20-M-MM | 41-828-3-01 | 20 degrees | Medium Band, 20 deg tilt |
Mix and Match Cables
This transducer uses the CHIRP Mix and Match system. Installation requires two parts – a base model plus one of the CHIRP Mix and Match (MMC) cables listed below.
Each base model has a 9 meter pigtail cable permanently attached. This cable ends in an Airmar 11-pin female connector. The Mix and Match cables are 1 meter long and have a male Airmar 11-pin connector at one end (to connect to the transducer pigtail) and a brand-specific connector at the other end (to connect to the sounder or fishfinder). If an owner changes their fishfinder or sounder, a different MMC cable can be installed without disturbing the transducer itself or needing to re-run cable through the boat.
| Cable Connector | Code | Airmar Part # | Length | Equipment |
|---|---|---|---|---|
| MMC-0 | 33-1359-01 | 1 meters | Bare wire applications | |
| MMC-11R-HM | 33-1402-01 | 1 meters | Raymarine High/High Wide/Medium Band 11-pin | |
| MMC-11R-LDB | 33-1357-01 | 1 meters | Raymarine Low and Dual-Band 11-pin | |
| MMC-12G | 33-1356-01 | 1 meters | Garmin orange 12-pin | |
| MMC-14HB | 33-1386-01 | 1 meters | Humminbird 14-pin | |
| MMC-8G | 33-1354-01 | 1 meters | Garmin blue 8-pin | |
| MMC-9N | 33-1394-01 | 1 meters | Navico 9-pin | |
| MMC-9N2 | 33-1395-01 | 1 meters | Navico Dual 9-pin | |
| MMC-BL | 33-1355-01 | 1 meters | Lowrance/Simrad blue 7-pin | |
| MMC-BL2 | 33-1358-01 | 1 meters | Lowrance/Simrad Dual Y-cable blue 7-pin | |
| MMC-HB | 33_1385-01 | 1 meters | Humminbird #9 |
Replacement Parts
| Part | Airmar Part # | Description |
|---|---|---|
| 02-136-01 | Stainless Hull Nut | |
| 09-950-01 | Rubber Washer | |
| 20-618-02 | Spacer |
Reviews
There are no reviews yet.